InstaVer Systems - KNX

E-learning Basic course KNX - English (INS-KNX-BC-EN)


Beschrijving
KNX basic course
The aim of the KNX basic course is to learn students how to design complete electrical systems, which are connected to a KNX bus system and put them into use.

For whom?
The KNX course is designed for service and maintenance engineers, project managers, planners, end users, etc.

During the virtual practicum the tasks are made available in a simulation film.

Course duration The experience of E-learning students indicates that the course takes about 30-50 hours. You have 30 days access to the course after purchase.
Certificate of participation

The course concludes with a theoretical test. After passing the test (with at least a mark of 7), you will automatically receive a one-time certificate of participation. You can obtain the KNX certificate and be enrolled as a partner in the KNX Association KNX, after taking an exam via an approved worldwide training center (incl. 12 hours physically practicum lessons).

Theory : based on the official KNX basic course book
Practicum: supported with spoken word simulation movies
Practicum: virtual practicum with ETS5
Previous education
The students should have knowledge of electrical systems.
Inhoud
  • Chapter 1 - KNX System arguments
  • Chapter 1 - KNX System arguments
  • Chapter 1 - Test KNX System arguments
  • Chapter 2 - KNX TP Topology
  • Chapter 2 - KNX TP Topology voorbeeld
  • Assignment 1 - Introduction: Assignment of physical addresses
  • Assignment 1 - Practice Simulation: Assignment of physical addresses
  • Assignment 2 - Introduction: Linking group addresses for functions
  • Assignment 2 - Practice Simulation: Linking group addresses for functions
  • Assignment 3 - Introduction & video: Create a new ETS5 project voorbeeld
  • Assignment 3 - Practice Simulation: Create a new ETS5 project
  • Assignment 4 - Introduction: Plans sensors and actuators to the bus line
  • Assignment 4 - Practice Simulation: Plans sensors and actuators to the bus line
  • Assignment 5 - Introduction & video: Importing product software
  • Assignment 5 - Practice Simulation: Importing product software
  • Assignment 6A - Introduction & video: Create a building list
  • Assignment 6A - Practice Simulation: Create a building list
  • Assignment 6B - Introduction & video: The placement of components in a building
  • Assignment 6B - Practice Simulation: The placement of components in a building
  • Chapter 2 - Test KNX TP Topology
  • Chapter 3 - KNX System overview
  • Chapter 3 - KNX System overview
  • Assignment 7 - Introduction & video: Configuring a contact and Operation
  • Assignment 7 - Practice Simulation: Configuring a contact and Operation
  • Chapter 3 - Test KNX System overview
  • Chapter 4 - KNX Bus Devices
  • Chapter 4 - KNX Bus Devices
  • Chapter 4 - Test KNX Bus Devices
  • Chapter 5 - KNX TP Installation
  • Chapter 5 - KNX TP Installation
  • Assignment 8 - Introduction: Numbering systems
  • Assignment 8 - Practice Simulation: Numbering systems
  • Assignment 9A - Introduction & video: Adding a touch sensor and parameterization
  • Assignment 9A - Practice Simulation: Adding a touch sensor and parameterization
  • Assignment 9B - Introduction & video: Changing a touch sensor function
  • Assignment 9B - Practice Simulation: Changing a touch sensor function
  • Assignment 9C - Introduction & video: Create group addresses - expand
  • Assignment 9C - Practice Simulation: Create group addresses - expand
  • Assignment 9D - Introduction & video: Group Addresses and central OFF
  • Assignment 9D - Introduction & video: Group Addresses and central OFF
  • Assignment 9E - Introduction & video: Full and partial programming
  • Assignment 9E - Practice Simulation: Full and partial programming
  • Assignment 9F - Introduction & video: Setting feedback and airing address
  • Assignment 9F - Practice Simulation: Setting feedback and airing address
  • Chapter 5 - Test KNX TP Installation
  • Chapter 6 - KNX Powerline 110
  • Chapter 6 - KNX Powerline 110
  • Chapter 7 - KNX RF
  • Chapter 7 - KNX RF
  • Chapter 8 - KNX Project Design ETS5: Basic
  • Chapter 8 - KNX Project Design ETS5: Basic
  • Assignment 10A - Introduction & video: Setup a dimmer
  • Assignment 10A - Practice Simulation: Setup a dimmer
  • Assignment 10B - Introduction & video: Setup a touch sensor for a dimmer
  • Assignment 10B - Practice Simulation: Setup a touch sensor for a dimmer
  • Assignment 10C - Introduction & video: Programming a dimmer with touch sensor
  • Assignment 10C - Practice Simulation: Programming a dimmer with touch sensor
  • Chapter 8 - Test KNX Project Design ETS5: Basic
  • Chapter 9 - KNX Project Design with ETS: Advanced
  • Chapter 9 - KNX Project Design with ETS: Advanced
  • Chapter 10 - KNX Commissioning
  • Chapter 10 - KNX Commissioning
  • Assignment 11A - Introduction & video: Configure a blind actuator
  • Assignment 11A - Practice Simulation: Configure a blind actuator
  • Assignment 11B - Introduction & video: Configuring a touch sensor for a blind
  • Assignment 11B - Practice Simulation: Configuring a touch sensor for a blind
  • Assignment 11C - Introduction & video: Assigning a security aspect
  • Assignment 11C - Practice Simulation: Assigning a security aspect
  • Assignment 11D - Introduction & video: Programming a blind actuator
  • Assignment 11D - Practice Simulation: Programming a blind actuator
  • Chapter 10 - Test KNX Commissioning
  • Chapter 11 - ETS5 Diagnostics
  • Chapter 11 - ETS5 Diagnostics
  • Assignment 12A - Introduction & video: Setting an actor with time delay
  • Assignment 12A - Practice Simulation: Setting an actor with time delay
  • Assignment 12B - Introduction & video: Setting a motion detector
  • Assignment 12B - Practice Simulation: Setting a motion detector
  • Assignment 12C - Introduction & video: Expand the system with a line coupler
  • Assignment 12C - Practice Simulation: Expand the system with a line coupler
  • Assignment 12D - Introduction & video: Placing a dummy component
  • Assignment 12D - Practice Simulation: Placing a dummy component
  • Assignment 12E - Introduction & video: Programming line coupler
  • Assignment 12E - Practice Simulation: Programming line coupler
  • Theory & practice exam KNX basic course
  • Final theory test
  • Registration for 12-hour physical lab sessions and the theory and practical exam
Voltooiingsregels
  • Alle onderdelen moeten voltooid zijn
  • Leidt naar een bewijs van deelname